It seems like our smartphones are getting bigger and bigger with each generation. Sometimes I see people holding what appears to be a tablet computer up next to their head. I doubt they know how ridiculous they look to the rest of us, and I wonder what pants today have pockets that big.
I certainly do like the convenience of the instant-on capabilities my smart phone gives me, but I still need my portable computer with its big screen and keyboard separate from my phone.
A few years ago, SATA-IO, the standards body, added a new feature to the Serial ATA (SATA) specification designed to further reduce battery consumption in portable computer products. This new feature, DevSleep, enables solid state drives (SSDs) to act more like smartphones, allowing you to go days without plugging in to recharge and then instantly turn them on and see all the latest email, social media updates, news and events.
Why not just switch the system off?
When most PC users think about switching off their system, they dread waiting for the operating system to boot back up. That is one of the key advantages of replacing the hard disk drive (HDD) in the system with a faster SSD. However, in our instant gratification society, we hate to wait even seconds for web pages to come up, so waiting minutes for your PC to turn on and boot up can feel like an eternity. Therefore, many people choose to leave the system on to save those precious moments… but at the expense of battery life.
Can I get this today?
To further extend battery life, the new DevSleep feature requires a signal change on the SATA connector. This change is currently supported only in new Intel® Haswell chipset-based platforms announced this June. What’s more, the SSD in these systems must support the DevSleep feature and monitor the signal on the SATA connector. Most systems that support DevSleep will likely be very low-power notebook systems and will likely already ship with an SSD installed using a small mSATA, M.2, or similar edge connector. Therefore, the signal change on the SATA interface will not immediately affect the rest of the SSDs designed for desktop systems shipping through retail and online sources. Note that not all SSDs are created equal and, while many claim support for DevSleep, be sure to look at the fine print to compare the actual power draw when in DevSleep.
At Computex last month, LSI announced support for the DevSleep feature and staged demonstrations showing a 400x reduction in idle power. It should be noted that a 400x reduction in power does not directly translate to a 400x increase in battery life, but any reduction in power will give you more time on the battery, and that will certainly benefit any user who often works without a power cord.
Not likely. But you might think that solving your computer data security problems is very well possible when someone tells you that TCG Opal is the key. According to its website, “The Trusted Computing Group (TCG) is a not-for-profit organization formed to develop, define and promote open, vendor-neutral, global industry standards, supportive of a hardware-based root of trust, for interoperable trusted computing platforms.”
That might take a bit to digest, but think about TCG as a group of companies creating standards to simplify deployment and increase adoption of data security. The consortium has two better known specifications called TCG Enterprise and TCG Opal.
Sorting through the alphabet soup of data security
“Our SED with TCG Opal provides FDE.” While this might look like a spoonful of alphabet soup, it is music to the ears of a corporate IT manager. Let me break it down for those who just hear fingernails on the chalkboard. A self-encrypting drive (SED) is one that embeds a hardware-based encryption engine in the storage device. One chief benefit is that the hardware engine performs the encryption, preserving full performance of the host CPU. An SED can be a hard disk drive (HDD) or a solid state drive (SSD). True, traditional software encryption can secure data going to the storage device, but it consumes precious host CPU bandwidth. The related term, full drive encryption (FDE), is used to describe any drive (HDD or SSD) that stores data in an encrypted form. This can be through either software-based (host CPU) or hardware-based (an SED) encryption.
Most people would assume that if their work laptop were lost or stolen, they would suffer only some lost productivity for a short time and about $1,500 in hardware costs. However, a study by Intel and the Ponemon Institute found that the cost of a lost laptop totaled nearly $50,000 when you account for lost IP, legal costs, customer notifications, lost business, harm to reputation, and damages associated with compromising confidential customer information. When the data stored on the laptop is encrypted, this cost is reduced by nearly $20,000. This difference certainly supports the need for better security for these mobile platforms.
When considering a security solution for this valuable data, you have to decide between a hardware-based SED and a host-based software solution. The primary problem with software solutions is they require the host CPU to do all of the encryption. This detracts from the CPU’s core computing work, leaving users with a slower computer or forcing them to pay for greater CPU performance. Another drawback of many software encryption solutions is that they can be turned off by the computer user, leaving data in the clear and vulnerable. Since hardware-based encryption is native to the HDD or SSD, it cannot be disabled by the end user.
In April 2013, LSI and a few other storage companies worked with the Ponemon Institute to better understand the value of hardware-based encryption. You can read about the details in the study here, but the quick summary is that hardware-based encryption solutions can offer a 75% total cost savings over software-based solutions, on average.
When is this available?
At the Computex Taipei 2013 show earlier this month, LSI announced availability of a firmware update for SandForce® controllers that adds support for TCG Opal. The LSI suite at the show featured TCG Opal demonstrations using self-encrypting SSDs provided by SandForce Driven™ member companies, including Kingston, A-DATA, Avant and Edge. (Contact SSD manufacturers directly for product availability.)
Imagine a bathtub full of water and asking someone to empty the tub while you turn your back for a moment. When you look again and see the water is gone, do you just assume someone pulled the drain plug?
I think most people would, but what about the other methods of removing the water like with a siphon, or using buckets to bail out the water? In a typical bathroom you are not likely to see these other methods used, but that does not mean they do not exist. The point is that just because you see a certain result does not necessarily mean the obvious solution was used.
I see a lot of confusion in forum posts from SandForce Driven™ SSD users and reviewers over how the LSI® DuraWrite™ data reduction and advanced garbage collection technology relates to the SATA TRIM command. In my earlier blog on TRIM I covered this topic in great detail, but in simple terms the operating system uses the TRIM command to inform an SSD what information is outdated and invalid. Without the TRIM command the SSD assumes all of the user capacity is valid data. I explained in my blog Gassing up your SSD that creating more free space through over provisioning or using less of the total capacity enables the SSD to operate more efficiently by reducing the write amplification, which leads to increased performance and flash memory endurance. So without TRIM the SSD operates at its lowest level of efficiency for a particular level of over provisioning.
Will you drown in invalid data without TRIM?
TRIM is a way to increase the free space on an SSD – what we call “dynamic over provisioning” – and DuraWrite technology is another method to increase the free space. Since DuraWrite technology is dependent upon the entropy (randomness) of the data, some users will get more free space than others depending on what data they store. Since the technology works on the basis of the aggregate of all data stored, boot SSDs with operating systems can still achieve some level of dynamic over provisioning even when all other files are at the highest entropy, e.g., encrypted or compressed files.
With an older operating system or in an environment that does not support TRIM (most RAID configurations), DuraWrite technology can provide enough free space to offer the same benefits as having TRIM fully operational. In cases where both TRIM and DuraWrite technology are operating, the combined result may not be as noticeable as when they’re working independently since there are diminishing returns when the free space grows to greater than half of the SSD storage capacity.
So the next time you fill your bathtub, think about all the ways you can get the water out of the tub without using the drain. That will help you remember that both TRIM and DuraWrite technology can improve SSD performance using different approaches to the same problem. If that analogy does not work for you, consider the different ways to produce a furless feline, and think about what opening graphic image I might have used for a more jolting effect. Although in that case you might not have seen this blog since that image would likely have gotten us banned from Google® “safe for work” searches.
I presented on this topic in detail at the Flash Memory Summit in 2011. You can read it in full here: http://www.lsi.com/downloads/Public/Flash%20Storage%20Processors/LSI_PRS_FMS2011_T1A_Smith.pdf
Tags: bathtub drain, controller, data reduction technology, DuraWrite, flash, flash controller, flash memory, Flash Memory Summit, NAND, over-provisioning, SandForce, SandForce Driven SSD, SATA, Serial ATA, solid state drive, TRIM
It may sound crazy, but hard disk drives (HDDs) do not have a delete command. Now we all know HDDs have a fixed capacity, so over time the older data must somehow get removed, right? Actually it is not removed, but overwritten. The operating system (OS) uses a reference table to track the locations (addresses) of all data on the HDD. This table tells the OS which spots on the HDD are used and which are free. When the OS or a user deletes a file from the system, the OS simply marks the corresponding spot in the table as free, making it available to store new data.
The HDD is told nothing about this change, and it does not need to know since it would not do anything with that information. When the OS is ready to store new data in that location, it just sends the data to the HDD and tells it to write to that spot, directly overwriting the prior data. It is simple and efficient, and no delete command is required.
However, with the advent of NAND flash-based solid state drives (SSDs) a new problem emerged. In my blog, Gassing up your SSD, I explain how NAND flash memory pages cannot be directly overwritten with new data, but must first be erased at the block level through a process called garbage collection (GC). I further describe how the SSD uses non-user space in the flash memory (over provisioning or OP) to improve performance and longevity of the SSD. In addition, any user space not consumed by the user becomes what we call dynamic over provisioning – dynamic because it changes as the amount of stored data changes.
When less data is stored by the user, the amount of dynamic OP increases, further improving performance and endurance. The problem I alluded to earlier is caused by the lack of a delete command. Without a delete command, every SSD will eventually fill up with data, both valid and invalid, eliminating any dynamic OP. The result would be the lowest possible performance at that factory OP level. So unlike HDDs, SSDs need to know what data is invalid in order to provide optimum performance and endurance.
Keeping your SSD TRIM
A number of years ago, the storage industry got together and developed a solution between the OS and the SSD by creating a new SATA command called TRIM. It is not a command that forces the SSD to immediately erase data like some people believe. Actually the TRIM command can be thought of as a message from the OS about what previously used addresses on the SSD are no longer holding valid data. The SSD takes those addresses and updates its own internal map of its flash memory to mark those locations as invalid. With this information, the SSD no longer moves that invalid data during the GC process, eliminating wasted time rewriting invalid data to new flash pages. It also reduces the number of write cycles on the flash, increasing the SSD’s endurance. Another benefit of the TRIM command is that more space is available for dynamic OP.
Today, most current operating systems and SSDs support TRIM, and all SandForce Driven™ member SSDs have always supported TRIM. Note that most RAID environments do not support TRIM, although some RAID 0 configurations have claimed to support it. I have presented on this topic in detail previously. You can view the presentation in full here. In my next blog I will explain how there may be an alternate solution using SandForce Driven member SSDs.
The term global warming can be very polarizing in a conversation and both sides of the argument have mountains of material that support or discredit the overall situation. The most devout believers in global warming point to the average temperature increases in the Earth’s atmosphere over the last 100+ years. They maintain the rise is primarily caused by increased greenhouse gases from humans burning fossil fuels and deforestation.
The opposition generally agrees with the measured increase in temperature over that time, but claims that increase is part of a natural cycle of the planet and not something humans can significantly impact one way or another. The US Energy Information Administration estimates that 90% of world’s marketed energy consumption is from non-renewable energy sources like fossil fuels. Our internet-driven lives run through datacenters that are well-known to consume large quantities of power. No matter which side of the global warming argument you support, most people agree that wasting power is not a good long-term position. Therefore, if the power consumed by datacenters can be reduced, especially as we live in an increasingly digitized world, this would benefit all mankind.
When we look at the most power-hungry components of a datacenter, we find mainly server and storage systems. However, people sometimes forget that those systems require cooling to counteract the heat generated. But the cooling itself consumes even more energy. So anything that can store data more efficiently and quickly will reduce both the initial energy consumption and the energy to cool those systems. As datacenters demand faster data storage, they are shifting to solid state drives (SSDs). SSDs generally provide higher performance per watt of power consumed over hard disk drives, but there is still more that can be done.
Reducing data to help turn down the heat
The good news is that there’s a way to reduce the amount of data that reaches the flash memory of the SSD. The unique DuraWrite™ technology found in all LSI® SandForce® flash controllers reduces the amount of data written to the flash memory to cut the time it takes to complete the writes and therefore reduce power consumption, below levels of other SSD technologies. That, in turn, reduces the cooling needed to further reduce overall power consumption. Now this data reduction is “loss-less,” meaning 100% of what is saved is returned to the host, unlike MPEG, JPEG, and MP3 files, which tolerate some amount of data loss to reduce file sizes.
Today you can find many datacenters already using SandForce Driven SSDs and LSI Nytro™ application acceleration products (which use DuraWrite technology as well). When we start to see datacenters deploying these flash storage products by the millions, you will certainly be able to measure the reduction in power consumed by datacenters. Unfortunately, LSI will not be able to claim it stopped global warming, but at least we, and our customers, can say we did something to help defer the end result.
Have you ever run out of gas in your car? Do you often risk running your gas tank dry? Hopefully you are more cautious than that and you start searching for a gas station when you get down to a ¼ tank. You do this because you want plenty of cushion in case something comes up that prevents you from getting to a station before it is too late.
The reason most people stretch their tank is to maximize travel between station visits. The downside to pushing the envelope to “E” is you can end up stranded with a dead vehicle waiting for AAA to bring you some gas.
Now most people know you don’t put gas in a solid state drive (SSD), but the pros and cons associated with how much you leave in the “tank” is very relevant to SSDs.
To understand how these two seemingly unrelated technologies are similar, we first need to drill into some technical SSD details. To start, SSDs act, and often look, like traditional hard disk drives (HDDs), but they do not record data in the same way. SSDs today typically use NAND flash memory to store data and a flash controller to connect the memory with the host computer. The flash controller can write a page of data (often 4,096 bytes) directly to the flash memory, but cannot overwrite the same page of data without first erasing it. The erase cycle cannot expunge only a single page. Instead, it erases a whole block of data (usually 128 pages). Because the stored data is sometimes updated randomly across the flash, the erase cycle for NAND flash requires a process called garbage collection.
Garbage collection is just dumping the trash
Garbage collection starts when a flash block is full of data, usually a mix of valid (good) and invalid (older, replaced) data. The invalid data must be tossed out to make room for new data, so the flash controller copies the valid data of a flash block to a previously erased block, and skips copying the invalid data of that block. The final step is to erase the original whole block, preparing it for new data to be written.
Before and during garbage collection, some data – valid data copied during garbage collection and the (typically) multiple copies of the invalid data – is in two or more locations at once, a phenomenon known as write amplification. To store this extra data not counted by the operating system, the flash controller needs some spare capacity beyond what the operating system knows. This is called over-provisioning (OP), and it is a critical part of every NAND flash-based SSD.
Over-provisioning is like the gas that remains in your tank
While every SSD has some amount of OP, some will have more or less than others. The amount of OP varies depending on trade-offs made between total storage capacity and benefits in performance and endurance. The less OP allocated in an SSD, the more information a user can store. This is like the driver who will take their tank of gas clear down to near-empty just to maximize the total number of miles between station visits.
What many SSD users don’t realize is there are major benefits to NOT stretching this OP area too thin. When you allocate more space for OP, you achieve a lower write amplification, which translates to a higher performance during writes and longer endurance of the flash memory. This is like the driver who is more cautious and visits the gas station more often to enable greater flexibility in selecting a more cost-effective station, and allows for last-minute deviations in travel plans that end up burning more fuel than originally anticipated.
The choice is yours
Most SSD users do not realize they have full control of how much OP is configured in their SSD. So even if you buy an SSD with “0%” OP, you can dedicate some of the user space back to OP for the SSD.
A more detailed presentation of how OP works and what 0% OP really means was presented at the Flash Memory Summit 2012 and can be viewed with this link for your convenience: http://www.lsi.com/downloads/Public/Flash%20Storage%20Processors/LSI_PRS_FMS2012_TE21_Smith.pdf
It pays to be the cautious driver who fills the gas tank long before you get to empty. When it comes to both performance and endurance, your SSD will cover a lot more ground if you treat the over-provisioning space the same way – keeping more in reserve.
Congratulations to Seagate on achieving this monumental milestone of shipping 2 billion hard disk drives (HDDs)! To put this in perspective, if you measured the Earth’s circumference in inches, it is only about 1.57 billion.
Those HDDs have used a lot of parts and intellectual property (IP), and LSI has been a very happy, long-time partner to Seagate providing read channel IP for nearly all of the 2 billion HDDs it has shipped. The read channel is a critical piece of technology inside the HDD that translates the magnetically encoded information on the rotating media to electronic signals that can be understood by the host computer. Advances in the LSI read channel IP over the years have also contributed to the continuing HDD capacity increases we depend upon today.
Seagate reported it took 29 years to ship its first billion drives and only 4 years for the second. This jaw-dropping growth is a stark reminder that the global data deluge continues to swell. Now more than ever, IT architects and managers need smarter ways – down to the silicon – to produce new storage and networking efficiencies and reduce costs.
Most people fully understand that electronics are useless without power, but what happens when devices lose power in the middle of operating? That answer is highly dependent on a number of variables including what type of electronic device is in question.
For solid state drives (SSDs) the answer depends on factors such as whether an uninterruptable power supply (UPS) is connected, what controller or flash processor is used, the design of the power circuit of the SSD, and the type of memory. If an SSD is in the middle of a write operation to the flash memory and power to the SSD is disconnected, many bad things could happen if the right safety measures are not in place. Many users do not think about all the non-user initiated operations the SSDs may be performing like background garbage collection that could be under way when the power fails. Without the correct protection, in most cases data will be corrupted.
According to the Nielsen company, 108.4 million viewers were tuned into the 2013 Super Bowl in New Orleans only to be shocked to witness the power go down for 34 minutes in the middle of the game. If power can be lost during such an incredibly high profile event such as this, it can happen just about anywhere.
Inside the New Orleans Superdome stadium operations and broadcast server rooms
Enterprise computing environments typically have multiple servers with data connections and lots of storage. Over the past few years, a larger percentage of the storage is kept on SSDs for the very active or “hot” data. This greatly improves data access time and reduces overall latency of the system. Enterprise servers are often connected to UPS systems that supply the connected devices with temporary power during a power failure.
Usually this is enough power to support uninterrupted system operations until power is restored, or at least until technicians can complete their current work and shut down safely. However there are many times when UPS systems are not deployed or fail to operate properly themselves. In those cases, the server will experience a power failure as abrupt as if someone had yanked the power cord from the wall socket.
The LSI® SandForce® flash controllers are at the heart of many popular SSDs sold today. The flash controller connects the host computer with the flash memory to store user data in fast non-volatile memory. The SandForce flash controllers are specifically engineered to operate in different environments, and the SF-2500/2600 FSPs are designed to provide the high level of data integrity required for enterprise applications. In the area of power failure protection, they include a combination of firmware (FW) and hardware circuitry that monitors the power coming into the SSD. In the event of a power failure or even a brown-out, the flash controller is alerted to the situation and hold-up capacitors in the SSD provide the necessary power and time for the controller to complete pending writes to the flash memory. This same circuit is also designed to prevent the risk of lower page corruption with Multi-level Cell (MLC) memory.
Watch out for SSD solutions that provide backup capacitors, but lack the necessary support circuitry and special firmware to ensure the data is fully committed to the flash memory before the power runs out. Even if these other special circuits are present, only truly enterprise SSDs that are meticulously designed and tested to withstand power failures are up to the task of storing and protecting highly critical data.
In the control room and down on the field
The usage patterns of non-enterprise systems like notebooks and ultrabooks call for a different power failure support mechanism. Realize that when you have a notebook or ultrabook system, you have a built in mini-UPS system. A power outage from the wall socket has no impact to the system until the battery gets low. At that point the operating system will tell the computer to shut down and that will be ample warning for the SSD to safely shut down and ensure the integrity of the data. But what if the operating system locks up and does not warn the SSD or the system is an A/C-powered desktop without a battery?
The LSI SF-2100/2200 FSPs are purpose-built for these client environments and operate with the assumption that power could disappear at any point in time. They use special FW techniques so that even without a battery present, as is the case with desktop systems, they greatly limit the potential for data loss.
The naked facts
It should be clear that the answer to the original question is highly dependent upon the flash controller at the heart of the SSD. Without having the critical features discussed above and designed into the LSI SandForce flash controllers, it is very possible to lose data during a power failure. The LSI SandForce flash controllers are engineered to withstand power failures like the one that hit New Orleans at the Super Bowl, but don’t expect them to fix wardrobe malfunctions.
Merging the working cultures of two different companies can be a very complex task. In my past experience with these situations I have not typically found the result to be highly positive for the employees of the incoming company.
As one example, the acquiring company may tell the employees they will be able to keep their startup environment and mentality, but within one or two quarters nearly all of those attributes are eliminated and the employees just become another cog in the bigger machine. After that the drive and creativity that was fostered with that startup mentality often disappears.
Year two and still happily married
In the first week of 2012, LSI completed the acquisition of SandForce, further expanding its growing coverage of flash memory technology IP. SandForce had grown significantly since its emergence from stealth mode in 2009 to become a leading provider of flash controllers for enterprise, cloud and client solid state storage solutions.
The SandForce team was kept in whole and created the Flash Components Division of LSI. The team even continues to reside in the same building it had occupied the prior year, further supporting the internal feeling of their original startup mentality. Most of the original culture of SandForce was kept intact and that enabled the transition into the larger LSI Corporation much easier for most people. Because those changes were spread out over a longer period of time it was easier for the team to digest with minimal disruption to their daily flow.
For the business side of the acquisition, there has been significant upside as a result of the merger. Over the last 14 months, both companies have invested significant time and resources to leverage the SandForce® flash controller technology across the company. LSI had already designed a high-end enterprise solution using the SandForce technology in their PCIe based Nytro™ product line. With both companies now under one umbrella, the engineering teams are free to develop advanced capabilities between the products to enable deeper integration that will result in greater customer benefits.
Greater efficiency … for the sake of customers
As a single larger company, LSI is now able to redistribute engineering and support resources as needed to better align with the quick expansion of flash memory storage solutions for its customers. It is also much easier to ensure a higher level of interoperability between related products and solutions. Many of the customers already purchasing LSI products can use the same sales and support teams already in place to access and incorporate a larger set of solutions from LSI.
Enterprise storage manufacturers have millions if not billions of dollars of revenue and their reputation at stake when they select new and emerging technologies like flash memory to provide storage for their customers. There is always a level of concern when these companies work with smaller startup organizations. The high-technology industry is full of company names that had a great technology, but for one reason or another they could not sustain the business and fell into oblivion. The acquisition of SandForce by LSI adds the support and confidence of a multi-billion dollar company to help assuage any possible concerns of those enterprise manufacturers.
Personally, as one of the early SandForce employees, I have found the acquisition to be very beneficial to everyone involved including employees, customers, and end users. I look forward to further advancements we will make to the flash industry as we continue to drive flash memory into the storage industry.